Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5836 visitantes y 
1 usuarios online.
Productos
Información
Destacado
Inicio >> JVC >> DLA-G150HTE Manual de Usuario
 
 0 artículo(s) en Su carrito 

JVC DLA-G150HTE
Manual de Usuario


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del JVC DLA-G150HTE Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como archivo PDF después de que lo compre.

El Manual del Propietario (a veces llamado Manual del Usuario o Guía del Usuario) contiene información sobre cómo utilizar su dispositivo. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
Replacing the Light-Source Lamp
The light-source lamp has a service life of approximately 1000 hours.
When the light-source lamp approaches the end of its service life, degradation progresses rapidly. The LAMP indicator and the message on the screen warn you that replacement of the lamp is required, as follows: Accumulated used hours of the light-source lamp 900 hours � The LAMP indicator lights up on the projector. � On the screen, �Lamp replacement� appears in red. To cancel this message, press the EXIT button. � Arrange for a new light-source lamp or replace the lightsource lamp a little earlier. * Every time the projector is turned on, the message appears. � The LAMP indicator blinks on the projector. � On the screen, �Warning Lamp replacement� appears in red and the word �Warning� blinks. Replace the light-source lamp. To cancel this message, press the EXIT button. However, the same message will appear every one hour. * Only OPERATE button to stop the projector and the EXIT button are operative. * Once the projector is turned off, the projector does not turn on unless the light-source lamp is replaced with new one. � The projector is forcibly shut off. * The projector does not turn on unless the light-source lamp is replaced with new one.

Replacing the Light-Source Lamp

I Be sure that the power cord is unplugged from the wall outlet.

1

Remove the lamp-replacement opening cover by loosening screws.
Loosen the two screws with a flat-end screwdriver. Screw

Note
Lamp replacement

� The screws are fitted so that they do not come off the lampreplacement opening cover.

EXIT

1000 hours

Warning Lamp replacement

Lamp-replacement opening cover

EXIT

1010 hours

ESPA�OL ITALIANO FRAN�AIS DEUTSH ENGLISH

No.51847 1-31

Purchase a new light-source lamps (Part No. : BHL5001-SU) from the authorized dealer where you purchased the projector, or consult the Service Center. CAUTIONS � If the projector is set up in a constricted place which is unsuitable for work, and if you perform replacement work there, this could cause injury. Move the projector to a place large enough for work, and then replace the light-source lamp. � Use a genuine product for the light-source lamp. If you use other than a genuine product, this could cause a malfunction. Also, never use an old light-source lamp. This could cause marked degradation in performance or explode, possibly causing the projector to malfunction or broken pieces to injure you. � Do not replace the light-source lamp immediately after the projector has been used. The temperature of the light-source lamp is still high and could cause a burn. Allow a cooling period of one hour or more before performing replacement. � Before starting light-source lamp replacement work, turn off the MAIN POWER switch, and disconnect the power cord from the wall outlet. If you perform the replacement work with the power cord connected, this could cause injury or electric shock. � The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the light-source lamp. If anything is unclear, please consult your dealer.

Be careful not to damage the claw.

2

Loosen the screws, raise the handle, and pull out the light-source lamp.
Loosen the two screws with a flat-end screwdriver. Screw

Note � The screws are fitted so that they do not come off the lightsource lamp.

Light-source lamp

Handle (To be continued on the next page)

DLA-G150HTE

57

58

Quizás también quiera comprar

$4.99

SX-K700 TECHNICS
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

CJ-V51 PIONEER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

SX-PR602 TECHNICS
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EV-S1000E SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

AG7330 PANASONIC
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EVO-9850 VOLUME 1 SONY
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.165 - Number of Queries: 125 - Query Time: 0.043